| Model NO. | WN |
| Control Mode | VIF control
Sensorless fluxvector control(SVC)(Above3.7KW) Close-loop vector control(FVC)(Above 3.7KW) |
| Maximum frequency | 0~600Hz |
| Brand | Wannan Motor |
| Carrier frequency | 0.5kHz~16kHz
The carrier frequency is automatically adjusted based on the load features |
| Input frequency resolution | Digital setting:0.01Hz
Analog setting: Maximum frequency0.025% |
| Start torque | GType:0.5Hz/150%(SVC);
PType:0.5Hz/100% |
| Speed range | 1:100(SVC) |
| Speed stability accuracy | +0.5%(SVC) |
| Overload capacity | G Type: 60s for 150% of the rated current3s for 180% of the rated current.
P Type: 60s for 120% of the rated current.
3s for 150% of the rated current. |
| Torque boost | Auto-boost;
Customized boost:0.1%~30.0% |
| V/F Curve | Straight-line V/F curve
Multi-pointV/F curve
N-powerV/F curve(1.2-power1.4-power1.6-power 1.8-power,square) |
| V/F separation | 2 types:complete separation half separation |
| Ramp Mode | Straight-line ramp
Four groups of acceleration/deceleration time with the range of0.006500.0s |
| DC Braking | DC braking DC braking frequency:0.00Hz~Maximum frequency Brakingtime:0.0s~36.0s
Braking action current value:0.0%~100.0% |
| JOG Control | JOGfreguencyrange:0.00Hz~50.00Hz
JOG acceleration/deceleration time:0.0s~6500.0s |
| Simple PLC,Multiple preset speeds | It implements up to 16 speeds via the simple PLC function or combination o terminal states |
| Onboard PID | It realizes process-controlled closed loop control system easily |
| Auto voitage regulation(AV.) | It can keep constant output voltage automatically when the mainsvoltage changes |
| Overvoltage/overcurrent stall control | The current and voltage are limited automatically during therunning process so as to avoid frequent tripping due to over voltage/over current |
| Rapid current limit | It helps to avoid frequent over current faults of the AC drive |
| Torque limit and control | It can limit the torque automatically and prevent frequent over current tripping during the running process.Torque control can be implemented in the FVC mode. |
| High performance | Control of asynchronous motor are implemented through the
high-performance current vector control technology |
| Rapid dip ride through | The load feedback energy compensates the voltage reduction so that the AC drive can continue to run for a short time |
| Rapid current limit | It helps to avoid frequent over current faults of the AC drive |
| Timing control | Timingrange:0.0Min~6500.0Min |
| Communication methods | RS-485 |
| Command source | Operation panel/Control terminals/Serial communication port
You can perform switchover between these sources in various ways |
| Frequency source | There are ten frequency sources
Digital setting,analog voltage setting analog current setting pulse setting serial port setting
You can perform switchover in various ways |
| Auxiliary frequency source | There are ten auxiliary frequency sourcesIt can implement fine tuning o auxiliary frequency and frequency synthesis |
| Input terminal | Standard: 4 digital input terminals(Below 5.5KW)/6 digital input terminals(Above7.5KW);
1 analog input terminal (Below 5.5KW)12 analog input terminals(Above
7.5KW);
1 voltage input (only support for 0~10Vabove 7.5KW),1voltage input(0~10V orcurrentinput(4~20mA) |
| Output terminal | 1 High-speed pulse output terminal(Open-collector)(Above3.7KW
1 replay output terminal(Below5.5KW)/2replayoutput terminals(Above
7.5KW)
1 analog output terminal(3.7KW~5.5KW)/2 analog output terminal(Above
7.5KW),Support for 4~20mAcurrent output or 0~10V voltage output |
| LED display | It displays the parameters |
| Key locking and function selection | It can lock the keys partially or completely and define the function range o some keys so as to prevent mal-function |
| Protection mode | Motor short-circuit detection at power-oninput/output phase loss protection over current protection, over voltage protection, under voltage protection overheat protection andoverload protection |
| Installation location | Indoor, free from direct sunlight,dust,corrosive gascombustible gas,oi smoke,vapor, drip or salt. |
| Transport Package | Carton/Wooden Case/Pallet |
| Trademark | WNM |
| Origin | China |
| HS Code | 8501520000 |
| Production Capacity | 2000PCS/Month |
